Handlebar risers (BMW, Ducati, Kawasaki, KTM LC4, Gas-Gas, Honda, MZ, Suzuki, Triumph, Yamaha), rise height of 20mm, 25mm, 30mm or 50mm - by SW-MOTECH

Provides a more upright, comfortable riding position by raising the original 7/8" (22mm) diameter tubular handlebar. No need to replace your handlebars - simply remove the original top clamp, place the riser between the handlebar and original bottom clamp, and reinstall top clamp using included hardware. Choose a rise height of 20mm (0.8"), 25mm (1"), 30mm (1.2"), or 50mm (2").

This item has replaced LEH.00.039.102 and LEH.00.039.103 and covers both of their application ranges.

For use with original top clamp or included matching SW-MOTECH top clamp.

No change of control cables, wiring, or hoses is required for most motorcycle models for 20mm, 25mm, or 30mm handlebar risers, HOWEVER:

The installer should always check for adequate cable/wiring/hose slack after installing any handlebar riser!

Simply put, the amount of cable slack varies on factory bikes even within a single model and year, so while 99.9% of all bikes will not need adjustment of cables to install handlebar risers, you should ALWAYS check for adequate slack after installation.

Available in anodized silver (s) or black (b)

Please follow all Torque Specifications to the letter Failure to do this will void warranty.

Confirmed fit list:
Aprilia
Pegaso 650, -'00

BMW
F650 Funduro, -'00 (does NOT fit F650GS models)
F650/ST, -'00 (does NOT fit F650GS models)
F650CS
F800ST
R80GS/ST ('80-'87)
R100GS/PD
R1100GS
R1150GS (extension of front brake hose required)
R1150GS Adventure
R1150R
R1150R Rockster
R1200RT, '05-
K1100RS, '02-
K100LT
K100RS
K100RT
K75/C
K75RT
K75S

Cagiva
Gran Canyon 900, '98-

Ducati
Multistrada DS1000 and DS620 (requires add-on Ducati screw kit)

Honda
599 (CB600 Hornet, naked model)
919 (CB900 Hornet, naked model)
NT700V Deauville
ST1100, '91-'94 (silver) (cannot use with stock handlebar plastic cover)
ST1100, '95- (black) (cannot use with stock handlebar plastic cover)
All Nighthawk models

Kawasaki
Eliminator 125
ER5
ER6F Ninja 650R, '06-'08
KLX650
KLR650A '87-07
KLR650E '08- Up to 30mm without changing cables.
Vulcan 750
ZR7
ZR 750 Zephyr
ZRX1200R (control cable extensions may be required)
DOES NOT FIT Z1000 or Z750S!
DOES NOT FIT '09- Ninja 650!

KTM
LC4 with tubular 7/8" diameter handlebars (measure hole distance before ordering)

MZ
Baghira

Suzuki
DL650 V-Strom, '04- (non-ABS)
DL650 V-Strom, '04- (ABS model requires an upper front brake line extension for installation of risers larger than 20mm)
DL1000 V-Strom, '02-
DRZ400
DR650SE, '96-
GS500E
GS500F
GSF600 & GSF600/S Bandit, all years
GSF650 & GSF650/S Bandit, all years
GSF1200 & GSF1200/S Bandit, all years
SV650N, -'02 (not for SV650S faired model)
SV650N, '03- (not for SV650S faired model)
SV1000N, '03- (not for SV1000S faired model)

Triumph
Adventurer 900
Bonneville 800
Legend TT 900
Scrambler 865, '07
Thunderbird
Tiger 1050, '07-
Tiger 955i, ’01-'06
Tiger 900, -‘01
Trident 750 & 900
Speed Triple 750, 900, 955i
Speed Triple 1050, '-07 (note: a rise height of more than 20mm requires a brake extension) 2008 and later model has 28mm bars and will not work with these risers
Street Triple 675, '08-'10 the Street Triple "R" model has 28mm bars and will not work with these risers

Note: Triumph bikes require optional screw kit that are 5mm shorter than those packed with the "universal" kit, which contains four M8x65 and four M8x70 screws.

Yamaha
FZ1 ('01-'05) - no extension needed
FZ1 ('06-'10)
FZ6 ('04-'10)
V-Max 1200, -07


These handlebar risers will only fit standard handlebar mounts that are symmetrical and perpendicular to each other; as such, these handlebar risers will not fit the Kawasaki Z1000, Kawasaki Z750S, or any other motorcycle with asymmetrical handlebar mounts.

If your handlebar mounts don't look similar to those pictured on this page, please contact us before ordering to confirm that the item will fit your bike.

This riser will fit your bike if:

(1) Your bar mounts are symmetrical and parallel;
(2) Your bars are 7/8" outer diameter;
(3) You have two M8 (8mm-diameter holes with standard M8 thread pitch) threaded holes in each of your two bar mounts; and
(4) The distance between the two holes in a single bar mount is 31-37mm on center. The distance between the two bar mounts is not a factor.


20 mm height risers include four M8x55 screws and four M8x60 screws.

25mm height risers include four M8x60 screws and four M8x65 screws.

30mm height risers include four M8x65 screws and four M8x70 screws.

50mm height risers include four M8x90 screws.

Customer Testimonial: John G - I purchased the 30MM risers for my '09' KLR650 and they work great. I don't think I could have gone higher. The electrical leads were almost maxed out. I took a 250 mile road trip and the risers relieved the tension in my shoulders and upper back that I have had on long trips in the past. I would recommend these riser for serious riders.